|
Mechanical
|
|
Format
|
Standard profile, half length, 8-lane PCI Express card
|
|
Cooling method
|
Air cooling, fan-cooled heatsink
|
|
Mounting
|
For insertion in a standard height, 8-lane or higher, PCI Express card slot
|
|
Connectors
|
-
'A', 'B', 'C', 'D' on bracket:
-
4x Micro-BNC female connectors
-
CoaXPress host interface
-
'EXTERNAL I/O' on bracket:
-
26-pin 3-row high-density female sub-D connector
-
I/O lines and power output
-
'INTERNAL I/O 1' and 'INTERNAL I/O 2' on PCB:
-
2x 26-pin 2-row 0.1" pitch pin header with shrouding
-
I/O lines and power output
-
'I/O EXTENSION' on PCB:
-
26-pin 2-row 0.05" pitch pin header with shrouding
-
I/O extension lines and power output
-
'AUXILIARY POWER INPUT' on module:
-
6-pin PEG power socket
-
12 VDC power input for PoCXP camera(s) and I/O power
-
'C2C-LINK' on module:
-
6-pin 2-row 0.1" pitch pin header
-
Card to card link
|
|
LED indicators
|
-
'A', 'B', 'C', 'D' on bracket:
-
Bi-color red/green LEDs
-
CoaXPress Host connector indicator
-
'FPGA STATUS LAMP' on PCB:
-
Bi-color red/green LED
-
FPGA status indicator
-
'BOARD STATUS LAMP' on PCB:
-
Bi-color red/green LED
-
Board status indicator
|
|
Switches
|
'RECOVERY' on PCB:
-
3-pin 1-row 0.1" header or 2-way DIP switch
-
Firmware emergency recovery
|
|
Dimensions
|
PCB L X H: 167.65 mm x 111.15 mm, 6.6 in x 4.38 in
|
|
Weight
|
196 g, 6.91 oz
|
|
Host bus
|
|
Standard
|
PCI Express 3.0
|
|
Link width
|
-
8 lanes
-
1 lane, 2 lanes or 4 lanes with reduced performance
|
|
Link speed
|
-
8.0 GT/s (PCIe 3.0)
-
5.0 GT/s (PCIe 2.0) with reduced performance
|
|
Maximum payload size
|
512 bytes
|
|
DMA
|
32- and 64-bit
|
|
Peak delivery bandwidth
|
7,800 MB/s
|
|
Effective (sustained) delivery bandwidth
|
6,700 MB/s (Host PC motherboard dependent)
|
|
Power consumption
|
Typ. 17.1 W (7.3 W @ +3.3V,9.8 W @ +12V), excluding camera and I/O power output
|
|
Camera / video inputs
|
|
Interface standard(s)
|
CoaXPress 1.0, 1.1, 1.1.1 and 2.0
|
|
Connectors
|
Four micro-BNC 75 Ohms (also known as HD-BNC?) CXP-12
|
|
Status LEDs
|
One CoaXPress Host connection status LED per connection
|
|
Number of cameras
|
-
Area-scan cameras:
-
One 1- or 2- or 4-connection camera
-
Two 1- or 2-connection cameras
-
Four 1-connection cameras
-
Line-scan cameras:
-
One 1- or 2- or 4-connection camera
-
Two 1- or 2-connection cameras
-
Four 1-connection cameras
|
|
Maximum aggregated camera data transfer rate
|
50 Gbit/s (5,000 MB/s)
|
|
Supported CXP down-connection speeds
|
1.25 GT/s (CXP-1), 2.5 GT/s (CXP-2), 3.125 GT/s (CXP-3), 5 GT/s (CXP-5), 6.25 GT/s (CXP-6), 10.0 GT/s (CXP-10), and 12.5 GT/s (CXP-12)
|
|
Supported CXP up-connection speeds
|
-
Low-speed 20.83... Mbps (CXP-1 to CXP-6)
-
Low-speed 41.66... Mbps (CXP-10, CXP-12)
|
|
Number of CXP data streams (per camera)
|
1 data stream per camera
|
|
Maximum CXP stream packet size
|
16,384 bytes
|
|
PoCXP (Power over CoaXPress)
|
-
PoCXP Safe Power:
-
17 W of 24V DC regulated power per CoaXPress connector
-
PoCXP Device detection and automatic power-on
-
Overload and short-circuit protections
-
On-board 12V to 24V DC/DC converter
-
A +12V power source must be connected to the AUXILIARY POWER INPUT connector using a 6-pin PEG cable
|
|
Camera types
|
-
Area-scan cameras:
-
Grayscale and color (YCbCr, YUV, RGB and Bayer CFA)
-
Single-tap (1X-1Y) progressive-scan
-
Two-tap (1X-2YE) on two distinct data streams ( '1-camera' firmware variant only)
-
Line-scan cameras and contact imaging sensors:
|
|
Camera pixel formats supported
|
-
Mono8, Mono10, Mono12, Mono14, Mono16
-
BayerXX8, BayerXX10, BayerXX12, BayerXX14, BayerXX16 where XX = GR, RG, GB, or BG
-
RGB8, RGB10, RGB12, RGB14, RGB16
-
RGBA8, RGBA10, RGBA12, RGBA14, RGBA16
-
YCbCr601_422_8, YCbCr601_422_10
-
YCbCr709_422_8, YCbCr709_422_10
-
YUV422_8, YUV422_10
-
Raw
|
|
Area-scan camera control
|
|
Trigger
|
-
Precise control of asynchronous reset cameras, with exposure control.
-
Support of camera exposure/readout overlap.
-
Support of external hardware trigger, with optional delay and trigger decimation.
|
|
Strobe
|
-
Accurate control of the strobe position for strobed light sources.
-
Support of early and late strobe pulses.
|
|
Line-scan camera control
|
|
Scan/page trigger
|
-
Precise control of start-of-scan and end-of-scan triggers.
-
Support of external hardware trigger, with optional delay.
-
Support of infinite acquisition, without missing line, for web inspection applications.
|
|
Line trigger
|
-
Support for quadrature motion encoders, with programmable noise filters, selection of acquisition direction and backward motion compensation.
-
Rate Converter tool for fine control of the pixel aspect ratio: Rate Conversion Ratio in the range 0.001 to 1000 with an accuracy better than 0.1%.
-
Rate Divider tool
|
|
Line strobe
|
-
Accurate control of the strobe position for strobed light sources.
|
|
On-board processing
|
|
On-board memory
|
4 GB
|
|
Image data stream processing
|
-
Unpacking of 10-/12-/14-bit to 16-bit with selectable justification to LSb or MSb
-
Optional swap of R and B components
-
Little endian conversion
|
|
Flat-field correction
|
Only available with the '1-camera' firmware variant
|
|
Input LUT (Lookup Table)
|
-
Monochrome 8-bit to 8-bit transformation
-
Monochrome 10-bit to 8-, 10- or 16-bit transformations
-
Monochrome 12-bit to 8-, 12- or 16-bit transformations
|
|
Bayer CFA to RGB decoder
|
'1-camera' firmware variant:
-
3x3 linear interpolation method
-
3x3 median-based interpolation method
|
|
Pixel binning
|
'1-camera' firmware variant:
-
2x2 and 4x4 binning windows
-
Bypass, sum and mean methods
|
|
CustomLogic firmware variants
|
-
'1-camera, customlogic' firmware variant for one 1- or 2- or 4-connection area-scan camera
-
'1-camera, line-scan, customlogic' firmware variant for one 1- or 2- or 4-connection line-scan camera
-
'2-camera, customlogic' firmware variant for two 1- or 2-connection area-scan cameras
-
'4-camera, customlogic' firmware variant for four 1-connection area-scan cameras
|
|
Data stream statistics
|
-
Measurement of:
-
Frame rate (Area-scan only)
-
Line rate
-
Data rate
-
Configurable averaging interval
|
|
Event signaling and counting
|
-
The application software can be notified of the occurrence of various events:
-
Standard event: the EVENT_NEW_BUFFER event notifies the application of newly filled buffers
-
A large set of custom events
-
Custom events sources:
-
I/O Toolbox events
-
Camera and Illumination control events
-
CoaXPress data stream events
-
CoaXPress host interface events
-
Each custom event is associated with a 32-bit counter that counts the number of occurrences
-
The last three 32-bit context data words of the event context data can be configured with event-specific context data:
-
Event-specific data
-
State of all System I/O lines sampled at the event occurrence time
-
Value of any event counter
|
|
General Purpose Inputs and Outputs
|
|
Number of lines
|
20 I/O lines:
-
4 differential inputs (DIN)
-
4 singled-ended TTL inputs/outputs (TTLIO)
-
8 isolated inputs (IIN)
-
4 isolated outputs (IOUT)
NOTE: The number of I/O lines can be extended using I/O modules attached to the I/O EXTENSION connector.
|
|
Usage
|
-
Any I/O input lines can be used by any LIN tool of the I/O Toolbox
-
Selected pairs of I/O input lines can be used by any QDC tool of the I/O toolbox to decode A/B signals of a motion encoder
|
|
Electrical specifications
|
-
DIN: High-speed differential inputs, up to 5 MHz, compatible with ANSI/EIA/TIA-422/485 differential line drivers and complementary TTL drivers
-
TTLIO: High-speed 5V-compliant TTL inputs or LVTTL outputs, compatible with totem-pole LVTTL, TTL, 5V CMOS drivers or LVTTL, TTL, 3V CMOS receivers
-
IIN: Isolated current-sense inputs with wide voltage input range up to 30V, compatible with totem-pole LVTTL, TTL, 5V CMOS drivers, RS-422 differential line drivers, potential free contacts, solid-state relays and opto-couplers
-
IOUT: Isolated contact outputs compatible with 30V / 100mA loads
NOTE: IIN and IOUT lines provide a functional isolation grade for the circuit technical protection. It does not provide an isolation that can protect a human being from electrical shock!
|
|
Filter control
|
-
Glitch removal filter available on all System I/O input lines
-
Configurable filter time constants:
-
for DIN and TTLIO lines: 50 ns, 100 ns, 200 ns, 500 ns, 1 μs
-
for IIN lines: 500 ns, 1 μs, 2 μs, 5 μs, 10 μs
|
|
Polarity control
|
Yes
|
|
Power output
|
Non-isolated, +12V, 1A, with electronic fuse protection
|
|
I/O Toolbox tools
|
The I/O Toolbox is a configurable interconnection of tools that generates events (usually triggers):
-
Line Input tool (LIN): edge detector delivering events on rising or falling edges of any selected input line.
-
Quadrature Decoder tool (QDC): a composite tool including:
-
A quadrature edge detector delivering events on selected transitions of selected pairs of input lines.
-
An optional backward motion compensator for clean line-scan image acquisition when the motion is unstable.
-
A 32-bit up/down counter for delivering a position value.
-
Device Link Trigger tool (DLT): delivers an event on reception of a valid high-speed CoaXPress 2.0 connection trigger packet message from the remote device.
-
User Actions Scheduler tool (UAS): to delegate the execution of 'User Actions' at a scheduled time or encoder position. Possible user actions include setting low/high/toggle any bit of the User Output Register or generation of any User Events.
-
Delay tool (DEL): to delay up to 16 events from one or two I/O toolbox event sources, by a programmable time or number of motion encoder ticks (any QDC events).
-
Divider tool (DIV): to generate an event every nth input events from any I/O toolbox event source.
-
Multiplier/divider tool (MDV): to generate m events every d input events from any I/O toolbox event source.
-
The 'Input Tools' (LIN, QDC, DLT and UAS) can be further processed by the 'Event Tools' (DEL, DIV and MDV) to generate any of the following "trigger" events:
-
The "cycle trigger" of the Camera and Illumination controller
-
The "cycle sequence trigger" of the Camera and Illumination controller
-
The "start-of-scan trigger" of the Acquisition Controller (line-scan only)
-
The "end-of-scan trigger" of the Acquisition Controller (line-scan only)
|
|
I/O Toolbox composition
|
Determined by the selected firmware variant:
-
'1-camera': 8 LIN, 1 QDC, 2 DLT, 1 UAS, 2 DEL, 1 DIV, 1 MDV, 2 C2C
-
'2-camera': 8 LIN, 1 QDC, 4 DLT, 1 UAS, 2 DEL, 1 DIV, 1 MDV, 2 C2C
-
'4-camera': 8 LIN, 4 QDC, 8 DLT, 1 UAS, 2 DEL, 4 DIV, 4 MDV, 2 C2C
-
'1-camera, line-scan': 8 LIN, 1 QDC, 2 DLT, 1 UAS, 2 DEL, 1 DIV, 1 MDV, 3 C2C
-
'2-camera, line-scan': 8 LIN, 2 QDC, 4 DLT, 1 UAS, 2 DEL, 2 DIV, 2 MDV, 3 C2C
-
'4-camera, line-scan': 8 LIN, 4 QDC, 8 DLT, 1 UAS, 4 DEL, 4 DIV, 4 MDV, 3 C2C
|
|
C2C-Link
|
|
Description
|
-
Accurate synchronization of the trigger and the start-of-exposure of multiple grabber-controlled area-scan cameras.
-
Accurate synchronization of the start-of-cycle, start-of-scan and end-of-scan of multiple grabber-controlled line-scan cameras.
|
|
Specification
|
-
C2C-Link synchronizes cameras connected to:
-
the same card
-
to different cards in the same PC (requires an accessory cable such as the "3303 C2C-Link Ribbon Cable" or a custom-made C2C-Link cable)
-
to different cards in different PCs (requires one "1636 InterPC C2C-Link Adapter" for each PC and one RJ 45 CAT 5 STP straight LAN cable for each adapter but the last one)
-
Maximum distance:
-
60 cm inside a PC
-
1200 m cumulated adapter to adapter cable length
-
Maximum trigger rate:
-
2.5 MHz for configurations using a single PC, or up to 10 PCs and 100 m total C2C-Link cable length
-
200 kHz for configurations up to 32 PCs and 1200m total C2C-Link cable length
-
Trigger propagation delay from master to slave devices:
-
Less than 10 ns for cameras on the same card or on different cards in the same PC
-
Less than 265 ns for cameras on different cards in different PCs (3 PCs and 40m total C2C-Link cable length)
|
|
Software
|
|
Host PC Operating System
|
-
Microsoft Windows 11, 10, 8.1, 7 for x86-64 (64-bit) processor architecture
-
Linux for x86-64 (64-bit) and AArch64 (64-bit) processor architectures
-
macOS for x86-64 (64-bit) and AArch64 (64-bit) processor architectures
|
|
APIs
|
-
EGrabber class, with C++ and .NET APIs: .NET assembly designed to be used with development environments compatible with .NET frameworks version 4.0 or higher
-
GenICam GenTL producer libraries compatible with C/C++ compilers:
-
'x86_64' dynamic library designed to be used with ISO-compliant C/C++ compilers for the development of x86-64 (64-bit) applications
-
'aarch64' dynamic library designed to be used with ISO-compliant C/C++ compilers for the development of AArch64 (64-bit) applications
|
|
Environmental conditions
|
|
Operating ambient air temperature
|
0 to +55 °C / +32 to +131 °F
|
|
Operating ambient air humidity
|
10 to 90% RH non-condensing
|
|
Storage ambient air temperature
|
-20 to +70 °C/ -4 to +158 °F
|
|
Storage ambient air humidity
|
10% to 90% RH non-condensing
|
|
Certifications
|
|
Electromagnetic - EMC standards
|
-
European Council EMC Directive 2014/30/EU
-
United States FCC rule 47 CFR 15
|
|
EMC - Emission
|
-
EN 55032:2015 / CISPR 32:2012 Class B
-
FCC 47 Part 15 Class B
|
|
EMC - Immunity
|
-
EN 55024:2010 / CISPR 24:2010
-
EN 55035:2017 / CISPR 35:2016
-
EN 61000-4-2:2009
-
EN 61000-4-3:2006
-
EN 61000-4-4:2004
-
EN 61000-4-6:2014
|
|
KC Certification
|
Korean Radio Waves Act, Article 58-2, Clause 3
|
|
Flammability
|
PCB compliant with UL 94 V-0
|
|
RoHS
|
European Union Directive 2015/863 (ROHS3)
|
|
REACH
|
European Union Regulation 1907/2006
|
|
WEEE
|
Must be disposed of separately from normal household waste and must be recycled according to local regulations
|
|
Ordering Information
|
|
Product code - Description
|
|
|
Optional accessories
|
|
